Activation Codes and Methods, Hardware Details, Sniffing
Post Reply
DeeVee
Posts: 2
Joined: Thu Jun 30, 2016 9:17 am

LG AD600 - Issue with modeswitching

Post by DeeVee » Fri Jul 01, 2016 7:16 am

I purchased an LG AD600 on the cheap awhile ago and am just starting to mess around with it in on Linux. There's scant information about it on the internet, but I did actually find a useful post from May on this forum linked here: http://www.draisberghof.de/usb_modeswit ... f=3&t=2529

I am running usb_modeswitchVersion 2.4.0 installed from source. Kernel is 3.13.0-46-generic.

I should also note that when I received this about 8 months ago I plugged this into a windows box in order to update the firmware which was necessary to enable LTE. I think this little modem is only able to do 3G unless it has the latest firmware.

As stated in the previous post, when plugged in the light turns red, eventually blinking blue, sometimes staying solid blue. Although on occassion it's blinked green and then stayed green. Not sure what that means with this device. It could have something to do with connecting to 3G/4G and having different colors depending. Running lsusb -vd 1004:6190 shows the following:

Code: Select all

Couldn't open device, some information will be missing
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x1004 LG Electronics, Inc.
  idProduct          0x6190
  bcdDevice           11.84
  iManufacturer           1
  iProduct                2
  iSerial                 3
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              4
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               1
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               1
 

Here is what the syslog looks like upon plugging in the device:

Code: Select all

Jun 30 23:46:47 thinkpad kernel: [ 9088.752183] usb 1-1: new high-speed USB device number 9 using ehci-pci
Jun 30 23:47:02 thinkpad kernel: [ 9104.112169] usb 1-1: new high-speed USB device number 10 using ehci-pci
Jun 30 23:47:02 thinkpad kernel: [ 9104.248789] usb 1-1: New USB device found, idVendor=1004, idProduct=6190
Jun 30 23:47:02 thinkpad kernel: [ 9104.248793] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jun 30 23:47:02 thinkpad kernel: [ 9104.248797] usb 1-1: Product: LGE USB Device
Jun 30 23:47:02 thinkpad kernel: [ 9104.248800] usb 1-1: Manufacturer: LGE
Jun 30 23:47:02 thinkpad kernel: [ 9104.248802] usb 1-1: SerialNumber: 012413000362674
Jun 30 23:47:02 thinkpad kernel: [ 9104.252584] usb-storage 1-1:1.0: USB Mass Storage device detected
Jun 30 23:47:02 thinkpad kernel: [ 9104.252694] scsi9 : usb-storage 1-1:1.0
Jun 30 23:47:03 thinkpad logger: usb_modeswitch: use overriding config file /etc/usb_modeswitch.d/1004:6190; make sure this is intended
Jun 30 23:47:03 thinkpad logger: usb_modeswitch: please report any new or corrected settings; otherwise, check for outdated files
Jun 30 23:47:03 thinkpad kernel: [ 9105.253941] scsi 9:0:0:0: CD-ROM            LGE      mobile           1.0  PQ: 0 ANSI: 0
Jun 30 23:47:07 thinkpad kernel: [ 9109.301798] sr0: scsi-1 drive
Jun 30 23:47:07 thinkpad kernel: [ 9109.302360] sr 9:0:0:0: Attached scsi CD-ROM sr0
Jun 30 23:47:07 thinkpad kernel: [ 9109.302512] sr 9:0:0:0: Attached scsi generic sg1 type 5
Jun 30 23:47:08 thinkpad usb_modeswitch: switch device 1004:6190 on 001/010

Here's the usb_modeswitch log looks like:

Code: Select all

USB_ModeSwitch log from Thu Jun  30 02:37:55 CDT 2016

Use global config file: /etc/usb_modeswitch.conf

Started via upstart
Raw args from udev: /1-5

Use top device dir /sys/bus/usb/devices/1-5
Check class of first interface ...
 Interface 0 class is 08.

----------------
USB values from sysfs:
  manufacturer  LGE
  product       LGE USB Device
  serial        012413000362674
----------------
bNumConfigurations is 1 - don't check for active configuration
ConfigList: /etc/usb_modeswitch.d/1004:6190 /usr/share/usb_modeswitch/1004:6190
SCSI attributes not needed, move on
Check config: /etc/usb_modeswitch.d/1004:6190
! matched. Read config data
Use config file from override folder /etc/usb_modeswitch.d
Logger is /usr/bin/logger
Delay time of 5 seconds
 wait is over, start mode switch
Unbinding driver
Command to be run:
usb_modeswitch -W -D -u -1 -b 1 -g 11 -v 1004 -p 6190 -f $flags(config)

Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are to be expected in the process)
--------------------------------

Read long config from command line

 * usb_modeswitch: handle USB devices with multiple modes
 * Version 2.4.0 (C) Josua Dietze 2016
 * Based on libusb1/libusbx

 ! PLEASE REPORT NEW CONFIGURATIONS !

DefaultVendor=  0x1004
DefaultProduct= 0x6190
TargetVendor=   0x1004
TargetProduct=  0x61a7

StandardEject=1
MessageContent="55534243123456702000000080000c85010101180101010101000000000000"
System integration mode enabled

Use given bus/device number: 001/011 ...
Look for default devices ...
 bus/device number matched
  found USB ID 1004:6190
   vendor ID matched
   product ID matched
 Found devices in default mode (1)
Get the current device configuration ...
Use interface number 0
Use endpoints 0x01 (out) and 0x81 (in)

USB description data (for identification)
-------------------------
Manufacturer: LGE
     Product: LGE USB Device
  Serial No.: 012413000362674
-------------------------
Sending standard EJECT sequence
Looking for active driver ...
 No active driver found. Detached before or never attached
Set up interface 0
Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 1 (CSW) ...
 Response reading failed (error -9)
 Device is gone, skip any further commands
ok:busdev
--------------------------------
(end of usb_modeswitch output)

Check success of mode switch for max. 20 seconds ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...
 Read attributes ...

Target config not matching - current values are
    1-5:1.0/bInterfaceClass:   08
    bConfigurationValue:       1
    bNumConfigurations:        1
    busnum:                    1
    devnum:                    11
    idProduct:                 6190
    idVendor:                  1004
    manufacturer:              LGE
    product:                   LGE USB Device
    serial:                    012413000362674

Mode switching may have failed. Exit

I made a config file in /etc/usb_modeswitch.d/ with the following:

Code: Select all

# LG AD600
TargetVendor=0x1004
TargetProduct=0x61a7
StandardEject=1
MessageContent="55534243123456702000000080000c85010101180101010101000000000000"
WaitBefore=5
It seems to have worked like a charm for the person who originally posted in the previous thread about the AD600, but I'm still stuck in what appears to be storage mode with modeswitching failing consistently. The only thing I've noticed in the logs that is different is at this stage

Code: Select all


 Trying to send message 1 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 1 (CSW) ...
 Response reading failed (error -9)

Whereas for the other poster has this in their log instead:

Code: Select all

Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 1 (CSW) ...
 Response successfully read (13 bytes).
Trying to send message 2 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 2 (CSW) ...
 Response successfully read (13 bytes).
Trying to send message 3 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 3 (CSW) ...
 Response reading failed (error -9)
 Device is gone, skip any further commands
ok:busdev
After originally writing this I looked at http://www.draisberghof.de/usb_modeswit ... erence.txt and saw the entry for the AD600 which said to use MessageContent="5553424312345678000000000000061b000000020000000000000000000000" instead. When I tried it out, it appears to have failed in the exact same way.

Needless to say I am completely stumped and I'd really like to get this working successfully on this old linux laptop.

LOM
Posts: 1286
Joined: Wed Jul 11, 2012 3:14 pm
Location: Koh Samui, TH

Re: LG AD600 - Issue with modeswitching

Post by LOM » Fri Jul 01, 2016 9:07 am

What usb id does lsusb show after you have done a manual eject of the virtual cdrom?

cmd line:

sudo eject /dev/sr0


The switch method for this modem is a standard eject sequence and you should not include any extra messages. The other thread states that you may need a delay before switching so change your config file to:

Code: Select all

# LG AD600
TargetVendor=0x1004
TargetProduct=0x61a7
StandardEject=1
WaitBefore=5
If you still get an error here:

Code: Select all

Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
 OK, message successfully sent
Read the response to message 1 (CSW) ...
 Response reading failed (error -9)
then I think your usb port can not provide enough power for the dongle.
The first of the two messages in a standard eject sequence can not make the dongle disappear from the bus as it has done for you, it is the second message in the sequence that does the actual switching.

DeeVee
Posts: 2
Joined: Thu Jun 30, 2016 9:17 am

Re: LG AD600 - Issue with modeswitching

Post by DeeVee » Fri Jul 01, 2016 11:48 am

I was getting this in my logs after plugging it back in:

Code: Select all

Jul  1 02:53:38 thinkpad kernel: [  904.688144] usb 1-1: new high-speed USB device number 12 using ehci-pci
Jul  1 02:53:53 thinkpad kernel: [  920.088170] usb 1-1: new high-speed USB device number 13 using ehci-pci
Jul  1 02:53:53 thinkpad kernel: [  920.224774] usb 1-1: New USB device found, idVendor=1004, idProduct=6190
Jul  1 02:53:53 thinkpad kernel: [  920.224779] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Jul  1 02:53:53 thinkpad kernel: [  920.224782] usb 1-1: Product: LGE USB Device
Jul  1 02:53:53 thinkpad kernel: [  920.224785] usb 1-1: Manufacturer: LGE
Jul  1 02:53:53 thinkpad kernel: [  920.224788] usb 1-1: SerialNumber: 012413000362674
Jul  1 02:53:53 thinkpad kernel: [  920.228569] usb-storage 1-1:1.0: USB Mass Storage device detected
Jul  1 02:53:53 thinkpad kernel: [  920.228682] scsi10 : usb-storage 1-1:1.0
Jul  1 02:53:54 thinkpad logger: usb_modeswitch: use overriding config file /etc/usb_modeswitch.d/1004:6190; make sure this is intended
Jul  1 02:53:54 thinkpad logger: usb_modeswitch: please report any new or corrected settings; otherwise, check for outdated files
Jul  1 02:53:54 thinkpad kernel: [  921.229970] scsi 10:0:0:0: CD-ROM            LGE      mobile           1.0  PQ: 0 ANSI: 0
Jul  1 02:53:59 thinkpad kernel: [  925.798435] sr0: scsi-1 drive
Jul  1 02:53:59 thinkpad kernel: [  925.798716] sr 10:0:0:0: Attached scsi CD-ROM sr0
Jul  1 02:53:59 thinkpad kernel: [  925.798848] sr 10:0:0:0: Attached scsi generic sg1 type 5
Jul  1 02:53:59 thinkpad kernel: [  925.822299] systemd-udevd[3320]: Failed to apply ACL on /dev/sr0: No such file or directory
Jul  1 02:53:59 thinkpad kernel: [  925.822315] systemd-udevd[3320]: Failed to apply ACL on /dev/sr0: No such file or directory
Jul  1 02:53:59 thinkpad usb_modeswitch: switch device 1004:6190 on 001/013
Jul  1 02:53:59 thinkpad kernel: [  925.835563] systemd-udevd[3319]: Failed to apply ACL on /dev/sr0: No such file or directory
Jul  1 02:53:59 thinkpad kernel: [  925.835577] systemd-udevd[3319]: Failed to apply ACL on /dev/sr0: No such file or directory
It kept saying "Failed to apply ACL on /dev/sr0: No such file or directory" no matter which USB port I used. Not exactly sure what changed and why it would start reporting that. I should mention that this is on a laptop running Trisquel 7.0 which is basically Ubuntu 14.04. Anyway, I did some searching and set DisableSwitching=1 in /etc/usb_modeswitch.conf which got rid of the ACL error and actually mounted the device on sr0.

Now to the interesting part. After ejecting sr0, lsusb showed the device Bus 001 Device 016: ID 1004:6183 LG Electronics, Inc.

lsusb -vd 1004:6183 shows this

Code: Select all

Bus 001 Device 016: ID 1004:6183 LG Electronics, Inc.
Couldn't open device, some information will be missing
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            2 Communications
  bDeviceSubClass         2 Abstract (modem)
  bDeviceProtocol         1 AT-commands (v.25ter)
  bMaxPacketSize0        64
  idVendor           0x1004 LG Electronics, Inc.
  idProduct          0x6183
  bcdDevice            1.00
  iManufacturer           1
  iProduct                2
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength          168
    bNumInterfaces          5
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              400mA
    Interface Association:
      bLength                 8
      bDescriptorType        11
      bFirstInterface         0
      bInterfaceCount         2
      bFunctionClass          2 Communications
      bFunctionSubClass       6 Ethernet Networking
      bFunctionProtocol       0
      iFunction               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass      6 Ethernet Networking
      bInterfaceProtocol      0
      iInterface              0
      CDC Header:
        bcdCDC               1.10
      CDC Union:
        bMasterInterface        0
        bSlaveInterface         1
      CDC Ethernet:
        iMacAddress                      4 (??)
        bmEthernetStatistics    0x00000000
        wMaxSegmentSize              22528
        wNumberMCFilters            0x0000
        bNumberPowerFilters              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               4
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    Interface Association:
      bLength                 8
      bDescriptorType        11
      bFirstInterface         2
      bInterfaceCount         2
      bFunctionClass          2 Communications
      bFunctionSubClass       2 Abstract (modem)
      bFunctionProtocol       1 AT-commands (v.25ter)
      iFunction               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              0
      CDC Header:
        bcdCDC               1.00
      CDC ACM:
        bmCapabilities       0x07
          sends break
          line coding and serial state
          get/set/clear comm features
      CDC Union:
        bMasterInterface        2
        bSlaveInterface         3
      CDC Call Management:
        bmCapabilities       0x03
          call management
          use DataInterface
        bDataInterface          3
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               4
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        3
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x05  EP 5 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        4
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x0a  EP 10 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8b  EP 11 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
In NetworkManager this shows up as LGELECTRONICSInc LG UDC-AHB Subsystem.

Your idea that the USB port isn't providing enough power is interesting because I remembered that it came with a special USB cable that let's it plug into two ports. One labeled Power+Data and the other just Power. Completely forgot about it. So, I'm now plugging it in via cable instead of directly into the computer.

I turned switching back on and plugged the device back in the Y-cable. Logs still look the same with response reading failed from message 1 so mode switching fails. Syslog is still showing as above with

Code: Select all

[ 6374.306837] systemd-udevd[4455]: Failed to apply ACL on /dev/sr0: No such file or directory

LOM
Posts: 1286
Joined: Wed Jul 11, 2012 3:14 pm
Location: Koh Samui, TH

Re: LG AD600 - Issue with modeswitching

Post by LOM » Fri Jul 01, 2016 1:35 pm

Your dmesg shows around 5 seconds between the time usb_modeswitch starts and the time sr0 is created so 5 seconds as WaitBefore is probably just a bit too short, raise it to 7 or 8.
The storage device sr0 obviously needs to be created and having settled before it can be ejected, regardless of it being done with a cmd line eject cmd or usb_modeswitch StandardEject (both of them do the same thing).

The new firmware you have flashed has a different usb id and different interface layout from what we know before, the interface layout is actually better than 1004:61a7 because it now has a functional cdc_acm ppp dialup interface pair, something 1004:61a7 didn't have.
Both of them has a direct network cdc_ether interface. We will add the new id in next issue of the usb_modeswitch data package but usb_modeswitch will switch the device even if it is not included.

vjfromgt
Posts: 1
Joined: Wed Apr 25, 2018 8:31 pm

Re: LG AD600 - Issue with modeswitching

Post by vjfromgt » Wed Apr 25, 2018 8:38 pm

Reviving old post.


cat /etc/usb_modeswitch.conf

[root@localhost etc]# cat /etc/usb_modeswitch.conf
# Configuration for the usb_modeswitch package, a mode switching tool for
# USB devices providing multiple states or modes
#
# Evaluated by the wrapper script /usr/sbin/usb_modeswitch_dispatcher
#
# To enable an option, set it to "1", "yes" or "true" (case doesn't matter)
# Everything else counts as "disable"


# Disable automatic mode switching globally (e.g. to access the original
# install storage)

DisableSwitching=0

# Disable check for MBIM module presence and configuration globally (to aid
# special embedded environments)

DisableMBIMGlobal=0

# Enable logging (results in a extensive report file in /var/log, named
# "usb_modeswitch_<interface-name>" and probably others

EnableLogging=0


# Optional increase of "delay_use" for the usb-storage driver; there are hints
# that a recent kernel default change to 1 sec. may lead to problems, particu-
# larly with USB 3.0 ports. Set this to at least 3 (seconds) in that case.
# Does nothing if the current system value is same or higher

#SetStorageDelay=4

# LG AD600
TargetVendor=0x1004
TargetProduct=0x61a7
StandardEject=1
MessageContent="55534243123456702000000080000c85010101180101010101000000000000"
WaitBefore=5




root@localhost etc]# tail -f /var/log/messages
Apr 25 14:34:22 localhost kernel: usb 1-4: New USB device found, idVendor=1004, idProduct=6190
Apr 25 14:34:22 localhost kernel: usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Apr 25 14:34:22 localhost kernel: usb 1-4: Product: LGE USB Device
Apr 25 14:34:22 localhost kernel: usb 1-4: Manufacturer: LGE
Apr 25 14:34:22 localhost kernel: usb 1-4: SerialNumber: 012413000275918
Apr 25 14:34:22 localhost kernel: usb-storage 1-4:1.0: USB Mass Storage device detected
Apr 25 14:34:22 localhost kernel: scsi host10: usb-storage 1-4:1.0
Apr 25 14:34:22 localhost systemd: Starting USB_ModeSwitch__1-4...
Apr 25 14:34:23 localhost usb_modeswitch: switch device 1004:6190 on 001/015
Apr 25 14:34:43 localhost systemd: Started USB_ModeSwitch__1-4.


[root@localhost etc]# lsusb
Bus 001 Device 015: ID 1004:6190 LG Electronics, Inc.
Bus 001 Device 002: ID 064e:d214 Suyin Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[root@localhost etc]#


[root@localhost etc]# wvdialcong
-bash: wvdialcong: command not found
[root@localhost etc]# wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: S0 S1 S2 S3


Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://alumnit.ca/wiki/?WvDial
[root@localhost etc]#

Post Reply