Automatic Activation, Hotplug and UDEV, Configuration
Post Reply
johnwayne
Posts: 5
Joined: 01 Sep 2012, 11:07

Huawei E173s-1 can not switch on embeded linux

Post by johnwayne » 01 Sep 2012, 13:41

hello guys.
I was trying to make a Huawei E173s-1 modem work on embeded linux these days.
I have tested it on windows 7 and fedora 16, it works well.

my kernel version: 2.6.34

Code: Select all

#uname -a
Linux  2.6.34 #3 SMP Sat Sep 1 14:41:51 CST 2012 armv7l GNU/Linux
the usb_modeswitch version:

Code: Select all

#usb_modeswitch --version

 * usb_modeswitch: handle USB devices with multiple modes
 * Version 1.2.3 (C) Josua Dietze 2012
 * Based on libusb0 (0.1.12 and above)

 ! PLEASE REPORT NEW CONFIGURATIONS !
the command "lsusb" is not configured with the busybox I used, so I print the file /proc/bus/usb/devices.

plug in the modem first time , the print is :

Code: Select all

usb 2-1: new high speed USB device using usb-ip9028 and address 2
usb 2-1: New USB device found, idVendor=12d1, idProduct=1c0b
usb 2-1: New USB device strings: Mfr=2, Product=1, SerialNumber=0
usb 2-1: Product: HUAWEI Mobile
usb 2-1: Manufacturer: HUAWEI
scsi2 : usb-storage 2-1:1.0
scsi3 : usb-storage 2-1:1.1
scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
scsi 2:0:0:0: Attached scsi generic sg0 type 5
sd 3:0:0:0: Attached scsi generic sg1 type 0
sd 3:0:0:0: [sda] Attached SCSI removable disk
the file /proc/bus/usb/devices:

Code: Select all

#cat /proc/bus/usb/devices

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1c0b Rev= 1.02
S:  Manufacturer=HUAWEI
S:  Product=HUAWEI Mobile
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
the data file I use is from "usb-modeswitch-data-20120531".
the content is:

Code: Select all

# Huawei E173s

TargetVendor=  0x12d1
TargetProductList="1c05,1c07,1c08"

MessageContent="55534243123456780000000000000011062000000100000000000000000000"
print after input usb_modeswitch:

Code: Select all


usb_modeswitch -v12d1 -p1c0b -c /etc/usb_modeswitch.d/12d1_1c0
b -s --verbos

Looking for target devices ...
 No devices in target mode or class found
Looking for default devices ...

   found matching product ID
   adding device
 Found device in default mode, class or configuration (1)
Accessing device 002 on bus 002 ...
Getting the current device configuration ...
 OK, got current device configuration (1)
Using first interface: 0x00
Using endpoints 0x0f (out) and 0x8f (in)
Inquiring device details; driver will be detached ...
Looking for active driver ...
 OK, driver found; name unknown, limitation of libusb1
 OK, driver "unkown" detached

SCSI inquiry data (for identification)
-------------------------
  Vendor Strusb 2-1: usbfs: process 822 (usb_modeswitch) did not claim interface 0 before use
ing: HUAWEI  
   Model String: Mass Storage    
Revision String: 2.31
-------------------------

USB description data (for identification)
------------------------usb 2-1: USB disconnect, address 2
-
Manufacturer: HUAWEI
     Product: HUAWEI Mobile
  Serial No.: not provided
-------------------------
Setting up communication with interface 0
Using endpoint 0x0f for message sending ...
Trying to send message 1 to endpoint 0x0f ...
 OK, message successfully sent
Resetting response endpoint 0x8f
 Could not reset endpoint (probably harmless): -6
Resetting message endpoint 0x0f
 Could not reset endpoint (probably harmless): -6
 Device is gone, skipping any further commands
-> Run lsusb to note any changes. Bye.

[root@H006.root]#usb 2-1: new high speed USB device using usb-ip9028 and address 3
usb 2-1: New USB device found, idVendor=12d1, idProduct=1c05
usb 2-1: New USB device strings: Mfr=2, Product=1, SerialNumber=0
usb 2-1: Product: HUAWEI Mobile
usb 2-1: Manufacturer: HUAWEI
scsi4 : usb-storage 2-1:1.3
scsi5 : usb-storage 2-1:1.4
scsi 4:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
scsi 5:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
scsi 4:0:0:0: Attached scsi generic sg0 type 5
sd 5:0:0:0: Attached scsi generic sg1 type 0
sd 5:0:0:0: [sda] Attached SCSI removable disk
it seemed the switch not finished, and the modem was recognized once more, and the idProduct changed from 0x1c0b to 0x1c05.

And now the content of file /proc/bus/usb/devices is:

Code: Select all



T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1c05 Rev= 1.02
S:  Manufacturer=HUAWEI
S:  Product=HUAWEI Mobile
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=8f(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0d(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I tried to add one line in "linux-kernel/drivers/usb/stoarge/unusual_devs.h",

Code: Select all

UNUSUAL_DEV(  0x12d1, 0x1c0b, 0x0000, 0x0000,
"HUAWEI MOBILE",
"Mass Storage",
US_SC_DEVICE, US_PR_DEVICE, usb_stor_huawei_e220_init,
0),
and add the corresponding lines in "linux-kernel/drivers/usr/serial/option.c", it did not work either.

Can any body help me ? thanks in advance.
Top
johnwayne
Posts: 5
Joined: 01 Sep 2012, 11:07

Post by johnwayne » 01 Sep 2012, 14:05

to add on, I have set "EnableLogging=1" in "\etc\usb_modeswitch.conf", but I can not find the right log file in "/var/log/" folder, I don't know why.
Top
johnwayne
Posts: 5
Joined: 01 Sep 2012, 11:07

Post by johnwayne » 01 Sep 2012, 14:26

dmesg print:

Code: Select all

#dmesg
y): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
scsi 18:0:0:0: Attached scsi generic sg0 type 5
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
sd 19:0:0:0: Attached scsi generic sg1 type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage 2-1:1.1: scan complete
usb-storage 2-1:1.0: scan complete
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x5 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
sd 19:0:0:0: [sda] Attached SCSI removable disk
usb-storage: storage_disconnect() called
usb-storage: -- usb_stor_release_resources
usb-storage: -- sending exit command to thread
usb-storage: *** thread awakened.
usb-storage: -- exiting
usb-storage: -- dissociate_dev
hub_events::portstatus change 1
usb 2-1: USB disconnect, address 10
usb-storage: storage_disconnect() called
usb-storage: -- usb_stor_release_resources
usb-storage: -- sending exit command to thread
usb-storage: *** thread awakened.
usb-storage: -- exiting
usb-storage: -- dissociate_dev
hub_events::portstatus change 1
usb 2-1: new high speed USB device using usb-ip9028 and address 11
usb 2-1: New USB device found, idVendor=12d1, idProduct=1c05
usb 2-1: New USB device strings: Mfr=2, Product=1, SerialNumber=0
usb 2-1: Product: HUAWEI Mobile
usb 2-1: Manufacturer: HUAWEI
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x12d1, Product: 0x1c05, Revision: 0x0102
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
scsi20 : usb-storage 2-1:1.3
usb-storage: *** thread sleeping.
usb-storage 2-1:1.3: device found
usb-storage 2-1:1.3: waiting for device to settle before scanning
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x12d1, Product: 0x1c05, Revision: 0x0102
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
scsi21 : usb-storage 2-1:1.4
usb-storage: *** thread sleeping.
usb-storage 2-1:1.4: device found
usb-storage 2-1:1.4: waiting for device to settle before scanning
hub_events::portstatus change 1
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=03 len=1
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=04 len=1
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: queuecommand called
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage:  12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage:  12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
scsi 20:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
scsi 21:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x3 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
scsi 20:0:0:0: Attached scsi generic sg0 type 5
usb-storage: queuecommand called
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage 2-1:1.3: scan complete
sd 21:0:0:0: Attached scsi generic sg1 type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage 2-1:1.4: scan complete
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x5 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: (Unknown Key): (unknown ASC/ASCQ)
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
sd 21:0:0:0: [sda] Attached SCSI removable disk
Top
Josh
Site Admin
Posts: 6593
Joined: 03 Nov 2007, 00:30

Post by Josh » 02 Sep 2012, 20:05

johnwayne wrote:it seemed the switch not finished
How did you come to that conclusion?

Did you read the explanations on the main documentation page of usb_modeswitch?

You need to install the data package as well. Your modem is fully supported since 2010. No need to tweak the "option" driver, the usb_modeswitch installation will add the USB ID to the driver 'on-the-fly'.

Top
johnwayne
Posts: 5
Joined: 01 Sep 2012, 11:07

Post by johnwayne » 03 Sep 2012, 16:44

Josh wrote:
johnwayne wrote:it seemed the switch not finished
How did you come to that conclusion?
the product id changed from 0x1c0b to 0x1c05, but the device nodes /dev/ttyUSB* did not show up.
and the following was added into /proc/bus/usb/devices:
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=8f(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0e(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0d(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I read the documentation of the main page for times, I think I followed the key points.

I use "busybox + mdev" in my system, so
Is udev essential for usb_modeswith when using in command line mode ?
"usbserial" and "option" must be configured as model in kernel, right ?
Top
Josh
Site Admin
Posts: 6593
Joined: 03 Nov 2007, 00:30

Post by Josh » 03 Sep 2012, 17:07

johnwayne wrote:the product id changed from 0x1c0b to 0x1c05, but the device nodes /dev/ttyUSB* did not show up.
So the mode switch completed fine, but no driver was bound.
johnwayne wrote:I use "busybox + mdev" in my system, so
Is udev essential for usb_modeswith when using in command line mode ?
It is not essential for the actual mode switch, but the wrapper which is usually started by udev takes care about the ad-hoc driver binding if the modem is not known to the driver yet.
johnwayne wrote:"usbserial" and "option" must be configured as model in kernel, right ?
They can either be compiled into the kernel or separate as modules. To operate the modem, they are of course essential.

To add a device ID "on the fly" to the driver, do this:

Code: Select all

# echo "12d1 1c05" > /sys/bus/usb-serial/drivers/option1/new_id
If you don't have that directory and file, you know that the driver is not active.

Top
johnwayne
Posts: 5
Joined: 01 Sep 2012, 11:07

Re: Huawei E173s-1 can not switch on embeded linux

Post by johnwayne » 04 Sep 2012, 13:53

I got the device nodes by

Code: Select all

echo "12d1 1c05" > /sys/bus/usb-serial/drivers/option1/new_id
Thank you very much, Josh. Thanks for your patience.
Top
Post Reply

Return to “Setup Discussion”