I have problem that with this device there is no modeswitch during restart (421:622 should change to 421:623). That of course means that I (or actually one older +70 person) can not use it for internet connection without extra maneuver...
Modeswitch happens only after I plugout/in device to usb.
With Fedora 16 I had to make some editing for config but that was "normal" device id things which happen often with new devices. Now (FC17) those were already included.
I see other people has same kind of problems but I did not find actual solution for the problem. Has there been any activities ongoing lately with this problem?
Is this udev or modeswitch problem?
I have udev and modeswitch logs with extra data. messages file is so big (170kB) that I don't want to copy it here. Is there some specific data in messages file which could help You?
It looks like devnum is different during power-on and plugin.
Thank You
Asko
Linux xxxxxx 3.6.10-2.fc17.i686.PAE #1 SMP Tue Dec 11 18:27:35 UTC 2012 i686 i686 i386 GNU/Linux
usb_modeswitch.i686 1.2.4-1.fc17 @updates
udev.i686 182-3.fc17 @updates
lsusb as a mass storage(=no modeswitch):
Code: Select all
Bus 001 Device 002: ID 0421:0622 Nokia Mobile Phones
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0421 Nokia Mobile Phones
idProduct 0x0622
bcdDevice 0.01
iManufacturer 2 Nokia
iProduct 1 Nokia Datacard
iSerial 3 64B47210398B20FC77FC702A5F205221D899677C
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
[Code: Select all
USB_ModeSwitch log from Tue Dec 25 18:36:29 EET 2012
Raw args from udev: /1-2:1.0
Using global config file: /etc/usb_modeswitch.conf
Using top device dir /sys/bus/usb/devices/1-2
----------------
USB values from sysfs:
manufacturer Nokia
product Nokia Datacard
serial 64B47210398B20FC77FC702A5F205221D899677C
----------------
bNumConfigurations is 1 - don't check for active configuration
SCSI attributes not needed, moving on
checking config: /etc/usb_modeswitch.d/0421:0622
! matched. Reading config data
Using config file from override folder /etc/usb_modeswitch.d
Logger is /usr/bin/logger
config: TargetVendor set to 0421
config: TargetProduct set to 0623
Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1
Command to be run:
usb_modeswitch -I -W -D -s 20 -u -1 -b 1 -g 2 -v 0421 -p 0622 -f $configBuffer
Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are to be expected in the process)
--------------------------------
Reading long config from command line
* usb_modeswitch: handle USB devices with multiple modes
* Version 1.2.4 (C) Josua Dietze 2012
* Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x0421
DefaultProduct= 0x0622
TargetVendor= 0x0421
TargetProduct= 0x0623
TargetClass= not set
TargetProductList=""
DetachStorageOnly=0
HuaweiMode=0
SierraMode=0
SonyMode=0
QisdaMode=0
GCTMode=0
KobilMode=0
SequansMode=0
MobileActionMode=0
CiscoMode=0
MessageEndpoint= not set
MessageContent="5553424312345678000000000000061b000000020000000000000000000000"
NeedResponse=0
ResponseEndpoint= not set
InquireDevice disabled
Success check enabled, max. wait time 20 seconds
System integration mode enabled
Use given bus/device number: 001/002 ...
Looking for default devices ...
bus/device number matched
searching devices, found USB ID 0421:0622
found matching vendor ID
found matching product ID
adding device
Found device in default mode, class or configuration (1)
Skipping the check for the current configuration
Using interface number 0
Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: Nokia
Product: Nokia Datacard
Serial No.: 64B47210398B20FC77FC702A5F205221D899677C
-------------------------
Looking for active driver ...
OK, driver found; name unknown, limitation of libusb1
OK, driver "unkown" detached
Setting up communication with interface 0
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Resetting response endpoint 0x81
Resetting message endpoint 0x01
Bus/dev search active, referring success check to wrapper. Bye.
ok:busdev
--------------------------------
(end of usb_modeswitch output)
Checking success of mode switch for max. 20 seconds ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Reading attributes ...
Target config not matching - current values are
1-2:1.0/bInterfaceClass: 08
bConfigurationValue: 1
bNumConfigurations: 1
busnum: 1
devnum: 2
idProduct: 0622
idVendor: 0421
manufacturer: Nokia
product: Nokia Datacard
serial: 64B47210398B20FC77FC702A5F205221D899677C
Mode switching may have failed. Exiting
Code: Select all
USB_ModeSwitch log from Tue Dec 25 18:40:00 EET 2012
Raw args from udev: /1-2:1.0
Using global config file: /etc/usb_modeswitch.conf
Using top device dir /sys/bus/usb/devices/1-2
----------------
USB values from sysfs:
manufacturer Nokia
product Nokia Datacard
serial 64B47210398B20FC77FC702A5F205221D899677C
----------------
bNumConfigurations is 1 - don't check for active configuration
SCSI attributes not needed, moving on
checking config: /etc/usb_modeswitch.d/0421:0622
! matched. Reading config data
Using config file from override folder /etc/usb_modeswitch.d
Logger is /usr/bin/logger
config: TargetVendor set to 0421
config: TargetProduct set to 0623
Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1
Command to be run:
usb_modeswitch -I -W -D -s 20 -u -1 -b 1 -g 3 -v 0421 -p 0622 -f $configBuffer
Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are to be expected in the process)
--------------------------------
Reading long config from command line
* usb_modeswitch: handle USB devices with multiple modes
* Version 1.2.4 (C) Josua Dietze 2012
* Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x0421
DefaultProduct= 0x0622
TargetVendor= 0x0421
TargetProduct= 0x0623
TargetClass= not set
TargetProductList=""
DetachStorageOnly=0
HuaweiMode=0
SierraMode=0
SonyMode=0
QisdaMode=0
GCTMode=0
KobilMode=0
SequansMode=0
MobileActionMode=0
CiscoMode=0
MessageEndpoint= not set
MessageContent="5553424312345678000000000000061b000000020000000000000000000000"
NeedResponse=0
ResponseEndpoint= not set
InquireDevice disabled
Success check enabled, max. wait time 20 seconds
System integration mode enabled
Use given bus/device number: 001/003 ...
Looking for default devices ...
bus/device number matched
searching devices, found USB ID 0421:0622
found matching vendor ID
found matching product ID
adding device
Found device in default mode, class or configuration (1)
Skipping the check for the current configuration
Using interface number 0
Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: Nokia
Product: Nokia Datacard
Serial No.: 64B47210398B20FC77FC702A5F205221D899677C
-------------------------
Looking for active driver ...
OK, driver found; name unknown, limitation of libusb1
OK, driver "unkown" detached
Setting up communication with interface 0
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Resetting response endpoint 0x81
Resetting message endpoint 0x01
Bus/dev search active, referring success check to wrapper. Bye.
ok:busdev
--------------------------------
(end of usb_modeswitch output)
Checking success of mode switch for max. 20 seconds ...
Reading attributes ...
Waiting for device file system (2 sec.) ...
Waiting for device file system (3 sec.) ...
Waiting for device file system (4 sec.) ...
Waiting for device file system (5 sec.) ...
Waiting for device file system (6 sec.) ...
Reading attributes ...
All attributes matched
Mode switching was successful, found 0421:0623 (Nokia: Nokia Datacard)
No vendor-specific class found, skip driver checking
Checking for AVOID_RESET_QUIRK kernel attribute
AVOID_RESET_QUIRK activated
All done, exiting