[nahka-apina]

I know that e3131 is not on 3g dongle support list of this tablet, but is there any way to get this combo working? I have searched all topics related to e3131 without success. Here are my log files



Ppp log:

Using port ttyUSB0 for connection
ATE1
OK
AT+CFUN=1
OK
AT+CGDCONT=1,"IP","data.dna.fi"
OK
ATD#777
NO CARRIERConnect script failed

Usblog:


PPP Widget version 1.3.1
USB_ModeSwitch log from Thu Mar 21 14:55:59 EET 2013

Raw args from udev: 1-1/1-1:1.0

Using top device dir /sys/bus/usb/devices/1-1
----------------
USB values from sysfs:
manufacturer HUAWEI
product HUAWEI Mobile Device
serial FFFFFFFFFFFFFFFF
----------------
SCSI attributes not needed, moving on
checking config: /data/data/de.draisberghof.pppwidget/app_tmp/12d1.151a
! matched. Reading config data
devList 1:
config: TargetVendor set to 12d1
config: TargetProductList set to 151b
Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1

Command to be run:
usb_modeswitch -I -W -D -s 20 -b 1 -g 2 -v 12d1 -p 151a -f $cB

Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are to be expected in the process)
--------------------------------

Reading long config from command line

* usb_modeswitch: handle USB devices with multiple modes
* Version 1.2.4 (C) Josua Dietze 2012
* Based on libusb0 (0.1.12 and above)

! PLEASE REPORT NEW CONFIGURATIONS !

DefaultVendor= 0x12d1
DefaultProduct= 0x151a
TargetVendor= 0x12d1
TargetProduct= not set
TargetClass= not set
TargetProductList="151b"

DetachStorageOnly=0
HuaweiMode=0
SierraMode=0
SonyMode=0
QisdaMode=0
GCTMode=0
KobilMode=0
SequansMode=0
MobileActionMode=0
CiscoMode=0
MessageEndpoint= not set
MessageContent="55534243123456780000000000000011062000000100000000000000000000"
NeedResponse=0
ResponseEndpoint= not set

InquireDevice disabled
Success check enabled, max. wait time 20 seconds
System integration mode enabled


Use given bus/device number: 001/002 ...
Looking for default devices ...
bus/device number matched
searching devices, found USB ID 12d1:151a
found matching vendor ID
found matching product ID
adding device
Found device in default mode, class or configuration (1)
Getting the current device configuration ...
OK, got current device configuration (1)
Using interface number 0
Using endpoints 0x01 (out) and 0x81 (in)

USB description data (for identification)
-------------------------
Manufacturer: HUAWEI
Product: HUAWEI Mobile Device
Serial No.: FFFFFFFFFFFFFFFF
-------------------------
Looking for active driver ...
OK, driver found; name unknown, limitation of libusb1
OK, driver "unkown" detached
Setting up communication with interface 0
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Resetting response endpoint 0x81
Could not reset endpoint (probably harmless): -34
Resetting message endpoint 0x01
Could not reset endpoint (probably harmless): -6
Device is gone, skipping any further commands
Bus/dev search active, referring success check to wrapper. Bye.

ok:busdev
--------------------------------
(end of usb_modeswitch output)

Checking success of mode switch for max. 20 seconds ...
Waiting for device file system (1 sec.) ...
Waiting for device file system (2 sec.) ...
Waiting for device file system (3 sec.) ...
Waiting for device file system (4 sec.) ...
Waiting for device file system (5 sec.) ...
Waiting for device file system (6 sec.) ...
Reading attributes ...
Mode switch has completed
Mode switching was successful, found 12d1:151d (HUAWEI: HUAWEI Mobile Device)
Device class of first interface is ff
Now checking for bound driver ...
Driver has bound, device is known

All done, exiting

[LOM]

Try with a GSM/UMTS dial cmd like ATD*99# or ATD*99***1# instead of the CDMA dial cmd you used.
I cant see anything else being wrong, modem gets switched and drivers gets loaded as they should.

[nahka-apina]

It works now! Thanks!