I'm trying to install my USB modem on Ubuntu 14.04, I followed the instructions in http://www.draisberghof.de/usb_modeswitch/ and then i tried to install the USB modem via the Shell Script file but I got the same error:
" This software will not run until you install 'QT3 Runtime Library' ", I then in the file /etc/usb_modeswitch.conf , I did EnableLogging=1 and here is the result:
Code: Select all
cat /var/log/usb_modeswitch_1-4
USB_ModeSwitch log from Sun Dec 13 17:14:03 EET 2015
Use global config file: /etc/usb_modeswitch.conf
Started via upstart
Raw args from udev: /1-4
Use top device dir /sys/bus/usb/devices/1-4
Check class of first interface ...
Interface 0 class is 08.
----------------
USB values from sysfs:
manufacturer ZTE,Incorporated
product ZTE WCDMA Technologies MSM
serial MF1900ZTED010000
----------------
bNumConfigurations is 1 - don't check for active configuration
Found packed config collection /usr/share/usb_modeswitch/configPack.tar.gz
ConfigList: /usr/share/usb_modeswitch/19d2:0154 /usr/share/usb_modeswitch/19d2:#linux pack/19d2:0154 pack/
SCSI attributes not needed, move on
Check config: /usr/share/usb_modeswitch/19d2:0154
! matched. Read config data
Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1
Unbinding driver
Command to be run:
usb_modeswitch -W -D -u -1 -b 1 -g 7 -v 19d2 -p 0154 -f $flags(config)
Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are to be expected in the process)
--------------------------------
Read long config from command line
* usb_modeswitch: handle USB devices with multiple modes
* Version 2.2.5 (C) Josua Dietze 2015
* Based on libusb1/libusbx
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x19d2
DefaultProduct= 0x0154
TargetVendor= 0x19d2
TargetProductList="0017,0117,2003"
StandardEject=1
NeedResponse=0
System integration mode enabled
Use given bus/device number: 001/007 ...
Look for default devices ...
bus/device number matched
found USB ID 19d2:0154
vendor ID matched
product ID matched
Found devices in default mode (1)
Use interface number 0
Use endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: ZTE,Incorporated
Product: ZTE WCDMA Technologies MSM
Serial No.: MF1900ZTED010000
-------------------------
Sending standard EJECT sequence
Looking for active driver ...
No active driver found. Detached before or never attached
Set up interface 0
Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Read the response to message 1 (CSW) ...
Response successfully read (13 bytes).
Trying to send message 2 to endpoint 0x01 ...
OK, message successfully sent
Read the response to message 2 (CSW) ...
Response successfully read (13 bytes).
Reset response endpoint 0x81
Reset message endpoint 0x01
ok:busdev
--------------------------------
(end of usb_modeswitch output)
Check success of mode switch for max. 20 seconds ...
Wait for device file system (1 sec.) ...
Read attributes ...
All attributes matched
Mode switching was successful, found 19d2:0117 (ZTE,Incorporated: ZTE WCDMA Technologies MSM)
Logger is /usr/bin/logger
Now check for bound driver ...
driver has bound, device is known
Check for AVOID_RESET_QUIRK kernel attribute
AVOID_RESET_QUIRK activated
All done, exit
Edit: The USB Modem is ID 19d2:0117 ZTE WCDMA